Back to top
GALA SHRINK FIT
GST : 27AAIFG8179Q1ZD

Call us now :08045804037

Send Inquiry Send Inquiry

Pipeline & Corrosion Protection Products
Product Image (GMWR 10/3 to GMWR 50/16)

Heat Shrink Tube for U-Bolt Coating - Pipe Support Corrosion Protection

Cross-linked polyolefin heat-shrink tube that coats the curved section of steel U-bolts, protecting the U-bolt-to-pipe contact point on pipe supports from crevice corrosion. 10 sizes from 10 to 50 mm. The tube only - not a U-bolt.

Send Inquiry
Request To Call Back
Product Image (GTWS 159 x 500 to GTWS 1016 x 500)

Heat Shrink Corrosion Protection Sleeve for Pipeline Weld Joints (GTWS)

Wrap-around heat-shrink sleeve that coats girth welds on buried or exposed steel pipelines. Cross-linked polyethylene backing with hot-melt adhesive bonds to steel and PE coating. 15 sizes for pipe OD 159 to 1016 mm, with closure patch.

Send Inquiry
Request To Call Back
Product Image (GMW 70/22 to GMW 863/250 (300 mm))

Heat Shrink Coupler for Post-Tensioning Duct Joints (GMW)

Adhesive-lined cross-linked polyolefin heat-shrink coupler that joins post-tensioning duct sections with a leak-tight seal. 17 sizes from 70 to 863 mm supplied ID, supplied as 300 mm pieces.

Send Inquiry
Request To Call Back
Product Image (GLC-SV 20/10 to GLC-SV 70/35)

Vented Thin Wall Heat Shrink Tube for Anchor Bolts (GLC-SV)

Black thin-wall 2:1 heat-shrink tube with longitudinal air-vent grooves inside, so it shrinks wrinkle-free over long bolts and bends without grease. For corrosion protection of wind-turbine anchor bolts, U-bolts and automotive parts.

Send Inquiry
Request To Call Back
Product Image (GPPC1 / GPPC2)

Heat Shrink Pre-Insulated Pipe Sealing Cap - Single and Double Outlet (GPPC)

Heat-shrinkable end cap that seals the insulation at the end of a pre-insulated pipe, shrinking onto the outer casing and onto one or two carrier pipes. Keeps water out of the insulation in service, transport and storage.

Send Inquiry
Request To Call Back
Product Image (GAC 0420 to GAC 0550)

Heat Shrink Anode Cap for Cathodic Protection (ANODECAP GAC)

Black heat-shrinkable stepped cap that seals the joint where the lead wire leaves a cathodic protection anode, giving moisture proofing, electrical insulation and strain relief at the wire exit. Six sizes.

Send Inquiry
Request To Call Back
Product Image (GCMW / GMW 70/22 to 863/250)

Heat Shrink Coupler for Corrugated HDPE Pipe Jointing (GCMW)

Adhesive-lined cross-linked polyolefin heat-shrink coupler for jointing corrugated HDPE pipe in water, sewer, drainage and cable-duct lines. 17 sizes from 70 to 863 mm supplied ID; an alternative to butt welding or snap-fit couplers.

Send Inquiry
Request To Call Back
X


GALA SHRINK FIT
GST : 27AAIFG8179Q1ZD
Send Inquiry
send inqSend Inquiry

Quick Links

Our Products

map
404/406, 4th Floor, Eureka Tower, New Link Road, Behind Toyota Showroom, Mindspace, Malad West Mumbai - 400064, Maharashtra, India
people
Mrs. Linette F D'souza (Executive Assistant to MD)
Mobile :08045804037
Send Inquiry Send Inquiry Send SMSSend SMS
logo
GALA SHRINK FIT All Rights Reserved.(Terms of Use)
Developed and Managed by Infocom Network Private Limited.