Back to top
Heat Shrink Busbar Tape - Adhesive Coated (BUSTAPE GMT-2L)
Heat Shrink Busbar Tape - Adhesive Coated (BUSTAPE GMT-2L)
Heat Shrink Busbar Tape - Adhesive Coated (BUSTAPE GMT-2L)
Heat Shrink Busbar Tape - Adhesive Coated (BUSTAPE GMT-2L)

Heat Shrink Busbar Tape - Adhesive Coated (BUSTAPE GMT-2L)

MOQ : 1 Piece

Heat Shrink Busbar Tape - Adhesive Coated (BUSTAPE GMT-2L) Specification

  • Installation Guideline
  • Wrapped with 2/3 overlap, end secured with glass-fibre tape, shrunk with a propane torch or hot-air blower
  • Coating Type
  • Adhesive coated on one side
  • Size
  • 50 mm wide x 15 m roll
  • Product Type
  • Heat shrinkable busbar insulating tape, adhesive coated
  • Rated Voltage
  • Medium-voltage busbars
  • Thickness
  • 1.0 mm +/- 0.10 mm
  • Application
  • Insulating MV busbar bends, joints and irregular connections; busbar repairs
  • Usage & Applications
  • Insulating MV busbar bends, joints and irregular connections; busbar repairs
  • Color
  • Red
  • Material
  • Cross-linked polyolefin with adhesive coating
 

Heat Shrink Busbar Tape - Adhesive Coated (BUSTAPE GMT-2L) Trade Information

  • Minimum Order Quantity
  • 1 Piece
  • Certifications
  • POWERGRID manufacturer approval, insulation sleeves and tapes up to 52 kV class, valid to 17 Feb 2028
 

About Heat Shrink Busbar Tape - Adhesive Coated (BUSTAPE GMT-2L)

BUSTAPE is Gala's heat-shrinkable, adhesive-coated insulating tape for medium-voltage busbars. Busbar runs are normally insulated with heat-shrink busbar sleeve, but bends, offsets, irregular joints and repairs often cannot take a tube. The tape is wrapped on instead and shrunk in place, giving the same kind of insulation and protecting the bar against accidental flashover and corrosion.

Installation: the tape is wound helically with a two-thirds overlap, adhesive side to the bar, running at least 75 mm onto the existing insulation. The free end is held with glass-fibre adhesive tape, and the wrap is shrunk with a propane torch or an electric hot-air blower until a bead of adhesive shows at the edge of each turn. As the tape shrinks it conforms to the contour and squeezes the adhesive into surface irregularities, forming a tough, waterproof seal that bonds to most surfaces and resists solvents once cured.

The tape is cross-linked polyolefin in red, supplied in rolls 50 mm wide and 15 m long with a 1.0 mm thickness, and shrinks at 125 deg C. It passed an inclined-plane tracking test (ASTM D2303 at 3.25 kV, ERDA 2018, against a 25 mm criterion). Gala holds POWERGRID manufacturer approval for insulation sleeves and tapes up to 52 kV class, valid to February 2028.

Switchgear builders, utilities and maintenance teams use it for bends, joints and repair work on busbars in switchgear, busducts and substations.

Manufactured by Gala in India. Datasheet and size selection on request.

Specifications

  • Brand: Gala
  • Product type: Heat shrinkable busbar insulating tape, adhesive coated
  • Material: Cross-linked polyolefin with adhesive coating
  • Colour: Red
  • Voltage rating: Medium-voltage busbars
  • Size range: 50 mm wide x 15 m roll
  • Wall type / thickness: 1.0 mm +/- 0.10 mm
  • Adhesive / sealant: Adhesive coated on one side
  • Standards tested to: ASTM D2303 inclined-plane tracking at 3.25 kV, passed against a 25 mm criterion (ERDA, 2018)
  • Application: Insulating MV busbar bends, joints and irregular connections; busbar repairs
  • Installation: Wrapped with 2/3 overlap, end secured with glass-fibre tape, shrunk with a propane torch or hot-air blower
  • Country of origin: India
  • Shrink temperature: 125 deg C
  • Approval: POWERGRID manufacturer approval, insulation sleeves and tapes up to 52 kV class, valid to 17 Feb 2028

Sizes

  • GMT-2L | roll width 50.0 mm min | roll length 15.0 m min | thickness 1.0 +/- 0.10 mm | red, adhesive coated

Applications: Switchgear and panel builders, busduct manufacturers, MV switchboards, substations, electricity utilities, power plants, transformer manufacturers, maintenance contractors

Tell us about your requirement
product

Price:

Quantity
Select Unit

  • 50
  • 100
  • 200
  • 250
  • 500
  • 1000+
Additional detail
Mobile number

Email

More Products in Switchgear Insulation Products Category

Heat Shrink Busbar Insulation Sheet - Adhesive Coated (BUSSHEET)

Heat Shrink Busbar Insulation Sheet - Adhesive Coated (BUSSHEET)

Minimum Order Quantity : 1 Piece

Product Type : Heat shrinkable busbar joint insulation sheet, adhesive coated

Usage & Applications : Insulating bolted busbar tees, elbows and straight joints in MV switchgear and panels

Installation Guideline : Cut to size, clamped over the joint and shrunk with a gas torch or hotair gun; reusable version closed with nylon fasteners

Material : Nontracking crosslinked polyolefin with adhesive coating

Size : For busbars 25 to 150 mm wide; sheet length up to 1200 mm

PVC Terminal Insulation Cap for Cable Lugs (TERMICAP TCV)

PVC Terminal Insulation Cap for Cable Lugs (TERMICAP TCV)

Minimum Order Quantity : 1 Piece

Product Type : Terminal insulation cap, pushon (not heatshrinkable)

Usage & Applications : Insulating and colourcoding crimped cable lugs and wireend terminals

Installation Guideline : Pushed over the crimped terminal by hand

Material : Flexible PVC

Size : 12 sizes; narrowend diameter 3.2 to 30 mm, length 15 to 79 mm

Busbar End Cap - Flexible PVC Push-On (BUSCAP)

Busbar End Cap - Flexible PVC Push-On (BUSCAP)

Minimum Order Quantity : 1 Piece

Product Type : Busbar end cap, pushon (not heatshrinkable)

Usage & Applications : Insulating the ends of live busbars in switchgear, panels and busducts

Installation Guideline : Pushed onto the busbar end by hand; removable and reusable

Material : Flexible PVC

Size : Busbar 15 x 5 mm to 200 x 12 mm (18 sizes)

PVC Busbar Insulating Shroud for Busbar Joints (BUSBOOT Vinyl)

PVC Busbar Insulating Shroud for Busbar Joints (BUSBOOT Vinyl)

Minimum Order Quantity : 1 Piece

Product Type : Busbar joint insulating boot (shroud), reusable, not heatshrinkable

Usage & Applications : Insulating bolted busbar joints, tees, elbows and standoff connections in switchgear and busducts

Installation Guideline : Placed over the joint and closed along the flanges with fasteners; removable and reusable

Material : Flexible PVC

Size : Busbars 10 mm to 280 mm wide; over 1,000 standard designs; custom designs to drawing